Warning: Illegal string offset 'allow_html' in [path]/geek/gars/mods/display/references.php on line 21
What Can I Do with a Cracked Cymbal? - Drum Building and Repair
drums drum set drummer
Drums resource and community for the online drummer
  The time is now 07:32 PM GMT -4.  
Search Drum Set Connect:
Site Features
Drum Forum
Drum Lessons
Drum Reviews
Drum Kit Photos
Drum T-Shirts
Premium Membership
Get in Touch
Link to us
Contact us
Find Drums

Go Back   Drum Forum at Drum Set Connect > Drum Lessons > Drum Building and Repair

Article Tools Display Modes
Prev Previous Post   Next Post Next
What Can I Do with a Cracked Cymbal?
What Can I Do with a Cracked Cymbal?
Smart ways to deal with a cracked cymbal
Published by Drum Set Connect
Post What Can I Do with a Cracked Cymbal?

1. Throw it away!
Accept the fact that it is dead and gone. There is nothing you can do.

2. Ask the dealer/manufacturer for a replacement.
Try to send it straight back to the dealer or even the cymbal manufacturer. At least try to get a new one before going into major surgery. For example, Zildjian's usually very good about replacing cracked cymbals, no questions asked.

3. Fix with epoxy
Cracked cymbals can be brought back to usefulness. The proceedure works like this. Force Epoxy into the crack. Strike the cymbal hard several times to vibrate glue deeper into the crack. Apply more Epoxy and strike several times again. Wipe away excess. Bake the cymbal in a 200 degree oven for about an hour. This hardens the Epoxy to a glassy consistancy. Let the cymbal cool naturally. Let stand for at least 24 hrs before playing. If done correctly, it works.

4. Fix by soldering/welding
An alternative way is to solder over the crack on both sides (standard solder for electronics). Polish the damaged part until it is all clean and shiny, this way the solder will grip properly. I found this to restore much of the original sound. Unfortunately, it tends to crack up again after about a day's playing (that is for cracks on the edge). I guess that stronger stuff (like welding) might last longer, but would probably melt the cymbal.

5. Fix by drilling
Cracked cymbals are no too easy to fix or work with. You may try drilling a small hole at each end of the crack to prevent further spread, and then widen the crack -- Like they did with the Liberty Bell the first few times it cracked. This will stop it from buzzing, but not much else.
If the crack starts from the edge, drill the other end and then make a wide, V-shaped notch starting from the hole.
Drilling may (with good luck) prevent the crack from getting bigger but it seldom improves the quality of the sound.

6. Fix by turning in the lathe
If the crack is on the outer edge and it's not too deep (towards the center), you can cut the cymbal smaller in the diameter. Of course, turning is likely to change the sound characteristics...

7. Make an effect cymbal out of it
Forget the old sound and try to figure out how you can get totally new, exciting, weird, previously unheard, nice sounding special effects out of it. You might try cutting the cymbal into a new size/shape. For example, just the cup of a large-cupped ride makes a cool bell.

Shop for cymbal care products at Musician's Friend
Article Tools


Article Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Similar Threads for: What Can I Do with a Cracked Cymbal?
Article Article Starter Category Comments Last Post
cracked cymbal Beamerzz Cymbals 21 10-25-2011 10:21 AM
Cymbal choking shakenbake Play the Drums - Drum Talk 6 06-29-2009 12:26 PM
Cymbal Stacking lukewarm Cymbals 5 04-08-2007 12:16 AM
Cymbal Heights Larry Play the Drums - Drum Talk 17 08-09-2005 03:24 PM

The time is now 07:32 PM GMT -4.

Powered by vBulletin® Version 3.8.2
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.

Article powered by GARS 2.1.8c ©2005-2006

      Copyright 2007 Teaguy Design. All Rights Reserved.  
About Us